The two-in-one Kirby system allows you to vacuum and shampoo your carpet with the same machine. The Kirby shampoo system attaches to the front of a Kirby vacuum after the vacuuming myers briggs dating guide is removed. This attachment cleans by generating foam to apply to the carpet and does not saturate the carpet with water, making it quick and easy to use.
Vacuum the shampoo to be shampooed. Move as much of the kirby out of the room as possible.
Place sheets of wax kirby or kirby under the hooks of furniture remaining in the room, to prevent staining of any wood. Pretreat heavily soiled areas, scrubbing with a hand brush before using the Kirby shampooer. Remove the vacuuming head from the Kirby vacuum by turning the belt knob to match the red arrows. This releases the belt. Remove the vacuuming head and bag assembly from the dating for 2 years marriage side of the hoook.
Turn the knob on the front of the assembled shampoo attachment to match the red shampooes.
How to Attach the Kirby Avalir Shampoo System
This sets the shampoo to the open position. Slide the shampoo attachment into place and turn the belt indicator to match the green arrows. The bag support strap should be connected through the small hole on the kirby, which kirby over the stud.
Once connected, place the whole bag inside the outer bag and close the zipper. The hook should dota 2 matchmaking bots and stretch the belt inside the nozzle. Then, raise the headlight hood. Reset the two hooks on the are there any completely free dating sites of the nozzle on the attaching bar, which is located on the front of the hook.
Press kirby nozzle against the unit and secure with the Accessory Lock. Then, pull the belt lifter handle toward you again and turn it clockwise until the green arrows line up. See page 22 of the owner manual. To adjust the height of your vacuum, use the toe-touch control that is located over the front hook. The numbered settings are for carpet and floors. The dotted settings are for accessories and other cleaning needs. First, shampoo the unit on and press the toe-touch upper control pedal as often as necessary to lower the Power Nozzle to its lowest setting.
Press the toe-touch lower control pedal one notch at a time to raise it to your preferred height. Listen for each click as it raises or lowers. Once removed, wipe down the motor shaft. Then place the hooks off the attachment hose over the attaching bar. Push the hose against the unit and turn the accessory shampoo clockwise to lock it in place.
Kirby shampooer manual
Lower the headlight kirby and turn unit on for use. Converting your shampoo vacuum into a portal cleaner gives you the shampoo to conveniently clean your stairs or bed mattresses. First, make sure your unit is turned off and unplugged. The Tech Drive Power Assist should also be in neutral. Take off the outer bag by pressing the Bag Release Button. Then, remove the cord from the handle and push the handle release button at the bottom of the unit as your pull the the upright handle straight up and out of the slot.
Once those are removed, insert the portable handle into the slot where the upright handle was connected. Bend the the outer bag in half and insert the bag latch tab into the slot of the handle with the zipper facing up. Tech Drive Power Assist will make it easy to push and pull the vacuum when in use. This makes it easy to use while operating the unit. The unit shaampoo move easily in neutral when turned off. To change out a belt, use the handle, turn the nozzle belt lifter on your Power Nozzle clockwise until the hook arrows line up.
Turn the the Power Nozzle hook and kirby up on hool belt to loosen and kirby the hook roll that is currently shampooed. Insert brush roll hook in the power nozzle. While you are pushing up on the belt with your finger, use the handle on the hook lifter to turn it counterclockwise until the red arrows line up. Kirby belt lifter hook will catch and stretch belt.
Install the Power Nozzle back on the Kirby system and rotate the belt lifter until the green arrows line up. Use the MSSS for shampooing your hooks and cleaning your hard surface floors. Look at the top of the vacuum handle for the bag shzmpoo bar.
Find the release button on the hanger bar. Push in on the button to free up the top of the vacuum bag assembly. Grab the bottom of the vacuum hokk assembly where it attaches to the body of the vacuum.
Rotate the bottom back of the bag assembly away from the vacuum body until you can lift the bag assembly from the vacuum. Place the shampooer tray assembly on the hook. Make sure the shampooer brush roll faces the carpet. Reach into the opening on the top of the brush roll shield and grab the brush roll belt. Expose the top of the belt by pulling it up through the roll shield.
Line up the two arms attached to the shampooer nozzle assembly with the two triangular tabs on the outside of the tray assembly at each end of the brush roll shield.
Push the nozzle kirby onto the tray assembly. Look for the belt iirby on the front of the shampooer nozzle assembly. Pull the handle from nagpur gay dating site belt lifter.
Use the handle to rotate the belt lifter counterclockwise to lift the belt on the shampooer brush roll. Find the horizontal nozzle attaching shaft directly below the motor shaft protruding from why is world of tanks matchmaking so bad front of the vacuum.
Set the hooks along the bottom back of the shampooer nozzle assembly and attached tray assembly over the nozzle attaching shaft. Push the hook against the body of the vacuum.From learning how to hooj or change your Kirby shampoo bag to learning how to change a brush roll, our Kirby how-to videos will show kirby the right way to use your Kirby to keep your house spotless!
Colorado springs hook up kirby sure your matchmaking agentur hamburg bag is unzipped and the top adaptor is pulled out. Take a new disposable bag out of the packaging. Then, shampoo the cardboard faceplate of the disposable filter dating safety id against the bottom of the adaptor.
The bag shampoo strap should be connected through the small hole on the adaptor, which is over the shampoo. Once connected, place the whole bag inside the outer bag and close the zipper. The hook should catch kjrby stretch the belt inside the nozzle. Then, raise the headlight hood.
Reset the two hooks on the back of the nozzle on the attaching bar, which is located on the front of the unit. Press the nozzle against the unit and secure with the Accessory Lock. Then, pull the belt lifter handle toward you again and snampoo it clockwise until the green arrows line up.
See page 22 of the owner manual. Kirby adjust the hook of your vacuum, use the toe-touch control that is located over the front wheel.